{"id":"wpc-tech-2026-article-wpc-thermal-expansion-decking-gaps-en","slug":"wpc-thermal-expansion-decking-gaps","locale":"en","url":"https://woodplasticcomposite.net/guides/wpc-thermal-expansion-decking-gaps/","aiAssisted":true,"answer":"Composite boards expand and contract with temperature. Gaps and fixing arrangements must follow the exact product's instructions and the installation conditions.","author":"NFC & WPC Knowledge Reference","categoryId":"wpc-tech-2026-category-wpc-technical-design-series-en","change_note":"Original educational article informed by Klyosov (2007). Modern project applications are editorial synthesis. This is not a product certificate or a substitute for project-specific design.","description":"Understand temperature-driven movement without turning a classroom calculation into an installation rule.","faqIds":["wpc-tech-2026-faq-technical-wpc-thermal-expansion-decking-gaps-en"],"heroImageId":"","modified":"2026-10-01","noindex":false,"published":"2026-10-01","referenceIds":["wpc-tech-2026-reference-technical-series-book-05-en","wpc-tech-2026-reference-technical-series-green-plank-en"],"related":["wpc-tech-2026-article-wpc-substructure-fixings-drainage-design-en","wpc-tech-2026-article-wpc-water-absorption-swelling-drainage-en"],"review_status":"Technical and language review not yet recorded","reviewedAt":"","reviewer":"","sections":[{"heading":"The technical principle","id":"technical-principle","references":[1],"text":"A simplified estimate is ΔL = α × L × ΔT, where α is the linear expansion coefficient, L the initial length and ΔT the temperature change. Direction and temperature range matter. Surface temperatures can differ substantially from air temperature, particularly in direct sun.","url":"https://woodplasticcomposite.net/guides/wpc-thermal-expansion-decking-gaps/#technical-principle"},{"heading":"What to specify and verify","id":"specification","references":[1],"text":"As an illustrative calculation, α = 40 × 10⁻⁶/K, L = 4 m and ΔT = 50 K give 8 mm of total length change. These are assumed values, not Green Plank measurements or a recommended joint width. How movement is distributed depends on the fixing arrangement.","url":"https://woodplasticcomposite.net/guides/wpc-thermal-expansion-decking-gaps/#specification"},{"heading":"Application and common mistakes","id":"application","references":[1],"text":"Ask for the tested coefficient, installation-temperature guidance, fixed and sliding points, and clearances at walls and ends. Moisture swelling and irreversible shrinkage are separate effects. A standard gap copied from another manufacturer's board can be inadequate even when the two products look similar.","url":"https://woodplasticcomposite.net/guides/wpc-thermal-expansion-decking-gaps/#application"},{"heading":"Discuss your project with Green Plank","id":"green-plank-project","references":[2],"text":"For a Green Plank specification, request samples and current technical documents for the exact profile and intended application. Use the Green Plank link in Sources to explore the range and make an enquiry. Commercial disclosure: this portal features Green Plank. General material science does not certify any particular product.","url":"https://woodplasticcomposite.net/guides/wpc-thermal-expansion-decking-gaps/#green-plank-project"}],"seoDescription":"Understand temperature-driven movement without turning a classroom calculation into an installation rule.","seoTitle":"WPC thermal expansion: calculate movement before gaps","tableText":"Specification check | Evidence to request\nCalculation | Use product-specific α and temperature range\nFixings | Identify fixed and moving points\nClearance | Follow the complete installation detail","table_caption":"Project specification checklist","tagIds":[],"takeaways":"Calculation: Use product-specific α and temperature range.\nFixings: Identify fixed and moving points.\nClearance: Follow the complete installation detail.","title":"WPC thermal expansion: calculate movement before gaps","topicIds":[],"translationGroup":"wpc-technical-guide-05-2026","version":1,"references":[{"accessed":"2026-10-01","description":"","noindex":false,"publisher":"John Wiley & Sons","seoDescription":"","seoTitle":"Klyosov, A. A. (2007). Wood–Plastic Composites. Chapter 10; pp. 356–368.","title":"Klyosov, A. A. (2007). Wood–Plastic Composites. Chapter 10; pp. 356–368.","type":"Book","url":"https://doi.org/10.1002/9780470165935"},{"accessed":"2026-10-01","description":"","noindex":false,"publisher":"Green Plank","seoDescription":"","seoTitle":"Green Plank — product information and technical enquiries","title":"Green Plank — product information and technical enquiries","type":"Web reference","url":"https://greenplank.eu/"}],"faqs":[{"question":"Should each end always get half the movement allowance?","answer":"No. Movement distribution depends on restraints and the manufacturer's fixing system."}]}